iPF610 Firmware Ver.1.41 (Firmware Update Tool Ver.3.40) for Windows
Content Id: 0400015606
Description
Outline
You can use this program to update the printer firmware version.
Update History
Modifications from Ver.1.40 to Ver.1.41 1. Fix the hung up issue rarely occurs when going into sleep mode. 2. Fix the paper jam with plain paper which rarely happens at the leading edge of roll paper. 3. The problem that the community name setting in SNMP setting was not processed correctly has been fixed. 4. Shutdown timer function has been added. -Shutdown timer After the printer goes into Sleep Mode, power will be turned off automatically when the situation that the printer is not operated continues until the time being set in advance by operation panel. Setup time:OFF/ 5 min./ 10 min./ 30 min./ 1 hour/ 4 hours/ 8 hours*/ 12 hours *Initial value when updating version.
Note: To fix the issue 2., please apply the MCT versions below to the printer and its driver after upgrading the firmware.
Windows 32bit 2.7205 Windows 64bit 2.7205 Mac OS X v10.4-v10.7 2.75 Mac OS X v10.2-v10.3 2.7405
Modifications from Ver.1.37 to Ver.1.40 1. The acquisition of serial number of main body by iWEMC supported 2. The failure of retrieving from sleep mode on rare occasions fixed 3. The failure of inability to print in HP/GL2 printing when file name contains 2-byte character(s) and the second byte is "5C" (back slash) fixed 4. The drive control in printing optimized
Modifications from Ver.1.36 to Ver.1.37 1. Support for obtaining printer serial numbers by iWEMC
Modifications from Ver.1.32 to Ver.1.36 1. In case the nozzles are clogged, formerly you would stop printing and check the printout, and then continue printing by pressing the Online key. Now it automatically checks the level of clogging, and if it is possible to print it will continue printing, and if it needs a printhead replacement, it will display a Replace Printhead message. This modification will greatly improve the workability. 2. Functions in the HP-GL/2 mode have been improved (to become faster).
System requirements
Use this program with the systems and the operating environments below.
Software: Microsoft Windows 8 32-bit edition, English edition Microsoft Windows 7 32-bit edition, English edition Microsoft Windows Server 2008 32-bit edition, English edition Microsoft Windows Vista 32-bit edition, English edition Microsoft Windows Server 2003 R2 32-bit edition, English edition Microsoft Windows Server 2003 32-bit edition, English edition Microsoft Windows XP Professional / Home Edition 32-bit edition, English edition Microsoft Windows 2000 Professional /Server , English edition
Hardware: Any computer running the software listed above.
Interface Connectivity: The printer and computer where this program is executed must be connected with either of the following methods.
- Connected via a TCP/IP network and capable of printing via the network. - Connected via a USB or IEEE 1394 port cable and capable of printing as a local printer.
Note: If you are using IEEE1394, IEEE1394 Class Driver Ver2.0 or later is needed.
Setup Instructions
(1) Switch the printer on. (2) Decompress it on your computer hard disk. (3) Execute the setup file. The imagePROGRAF Firmware Update Tool is installed. (4) From the Start menu, select Programs to execute imagePROGRAF Firmware Update Tool.
Caution
The following limitations apply to the use of this program. Before using the program, make sure that you understand these limitations.
* You must log into Windows as an Administrator before the installation.
* Before you start the firmware version update program, close any other applications that are running.
* Do not try to use the printer while the firmware version update program is running. If a print job is executing, cancel the print job or wait for the job to finish before you execute the version update program.
* Never switch off the target printer while the firmware version update program is running.
* If the firmware version update fails while writing to the flash ROM, you may not be able to start the printer. In this case, contact a Canon service center or the dealer where you purchased the printer.
File information
File Name : iPF610-FUT-Win-141.exe File Type : FA File Size : 14036992KB
Canon Driver Downloads is for the support of Canon Products SOLD IN AUSTRALIA AND NEW ZEALAND ONLY. It includes drivers and demonstration software for Canon brand printers, scanners, cameras and other Canon products.
DISCLAIMER: CANON AUSTRALIA PTY LTD MAKES NO GUARANTEES OF ANY KIND WITH REGARD TO ANY PROGRAMS, FILES, DRIVERS OR ANY OTHER MATERIALS CONTAINED ON OR DOWNLOADED FROM THIS, OR ANY OTHER, CANON SOFTWARE SITE. ALL SUCH PROGRAMS, FILES, DRIVERS AND OTHER MATERIALS ARE SUPPLIED "AS IS." CANON DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. CANON AUSTRALIA PTY LTD SHALL NOT BE HELD LIABLE FOR ERRORS CONTAINED HEREIN, OR FOR LOST PROFITS, LOST OPPORTUNITIES, CONSEQUENTIAL OR INCIDENTAL DAMAGES INCURRED AS A RESULT OF ACTING ON INFORMATION, OR THE OPERATION OF ANY SOFTWARE, INCLUDED IN THIS SOFTWARE SITE.
Export: Some of the software is subject to export controls under the U.S. Export Administration Regulations (EAR), and anyone receiving the software cannot export the software without a license or other authorisation of the U.S. Canon will not be liable for any loss of whatsoever nature incurred as a result of this prohibition.
Applicable software includes;
- Software using OS created by US companies
- Driver software (printer driver, fax driver),
- Utility software (Network ScanGear),
- Application software (imageWARE products),
- Support tool (SST, NAVI, etc)
- Firmware of the device (main body)
and any further software that may from time to time be added to this list.